CFM/CMM Thermo-Anemometer with built-in non-contact IR Thermometer measure remote surface temperature to 500ºC (932ºF) and 30:1 distance to spot ratio.
การแสดงผลพร้อมกันของการไหลของลมหรืออุณหภูมิความเร็วลมโดยรอบ / Simultaneous display of Air Flow or Air Velocity plus Ambient Temperature
ง่ายต่อการตั้งค่าการจัดเก็บพื้นที่หน่วยความจำ (ตารางเซนติเมตร) จะถูกจัดเก็บไว้ภายในของมิเตอร์สำหรับเปิดเครื่องในครั้งต่อไป / Easy to set Area dimensions (cm2) are stored in the meter’s internal memory for the next power on
0.01/ วินาที / Resolution of 0.01m/sec
การไหลของอากาศเฉลี่ยประมาณ 20 ทิศทาง / 20 points average for Air Flow
หน้าจอแสดงผลแบบแอลซีดีขนาดใหญ่(ตัวเลขได้ถึง9999ตัว) / Super large (9999 counts) LCD Backlit Display
MAX / MIN (Temperature) Used to record and store the highest, lowest readings for air temperature.
°C °F HOLD (อุณหภูมิ) ปุ่มองศาเซลเซียส องศาฟาเรนไฮต์(อุณหภูมิ) กดปุ่มหน้าจอเพื่อหยุดอ่านอุณหภูมิ กดอีกครั้งเพื่อล๊อคหน้าจอ กดสวิตซ์ค้าง3วินาทีระหว่าง °C และ °F เครื่องวัดจะส่งเสียงบี๊บสองครั้งเพื่อระบุการเปลี่ยนแปลง
°C °F HOLD (Temperature) Press to freeze the displayed temperature reading. Press again to unlock the display. Press and hold for 3 seconds to switch between °C and °F Meter will beep twice to indicate change.
the vane plug is inserted in the meter’s sensor jack at the top of the meter. The plug and jack are keyed so that the plug can only fit in the jack one way.
Turn the plug carefully until it lines up with the jack and then firmly push the plug in place. Do not apply undue force or try to twist the plug side-to-side.
3. หากใบพัดไม่ได้เชื่อมต่อกับมิเตอร์หรือเซ็นเซอร์ชำรุด จอ LCD จะแสดง OL แทนการอ่านค่าอุณหภูมิ
If the vane is not connected to the meter or if the sensor is defective, the LCD display will indicate OL in place of a Temperature reading.
Air Velocity Measurements (Single Point) การวัดความเร็วลม (จุดเดี่ยว)
1. Turn on the meter using the ON/OFF button. >> เปิดมิเตอร์โดยใช้ปุ่มเปิด / ปิด
Press UNITS button to select the desired unit of measure. NOTE: At power up the meter will display the last unit of measure previously entered. >> กดปุ่ม UNITS เพื่อเลือกหน่วยวัดที่ต้องการ , กดปุ่ม NOTE : เมื่อเปิดเครื่องมิเตอร์จะแสดงหน่วยการวัดสุดท้ายที่ ป้อนก่อนหน้านี้
2. Place the sensor in the air stream. Ensure that the air enters the vane as indicated by the arrow sticker <—- placed inside the vane. >> วางเซ็นเซอร์ในกระแสลม ตรวจสอบให้แน่ใจว่าอากาศเข้าสู่ใบพัดตามที่ระบุโดยสติกเกอร์ลูกศร <—- ที่วางไว้ภายในใบพัด
View the readings on the LCD Display. The large main LCD display shows the Air Velocity reading. The upper right LCD sub-display shows the temperature reading. >> ดูการอ่านบนหน้าจอ LCD , หน้าจอ LCD หลักๆมีขนาดใหญ่แสดงการอ่านความเร็วลม
มุมด้านข้างของใบพัด
เครื่องวัดความเร็วลม STINTERTRADE
ลูกศร ที่ปล่อยให้ลมผ่าน
Air Velocity Averaging Mode โหมดเฉลี่ยค่าความเร็วลม
The average reading will be displayed and number of readings measured will appear in the upper right hand corner of the display. After 5 seconds, the display will return to the current reading.